Buy Now >>
PKT's NEW Dellorto slide tool. Same great tool for loosening the slide while retaining all components (cable, spring & brass cable retainer) while making clip adjustments. We included a needlle clip pocket that allows easy clip adjustments without losing your clip in the grass. A new lanyard hole has also been added. Black anodized with laser engraving. Sold individually.
Lanyard & needle not included.
Buy Now >>
Buy Now >>
Introducing the PKT
LO206 15 Degree Motor Mount. Why 15 degree? This will allow you to move your Briggs
motor further forward than other mounts on the market. Why is that important? It allows your kart to perform
better by freeing it up. Another plus is the exhaust is higher keeping it safer in rear end collisions.
Our design has 3 motor
locations from side to side. We have incorporated a front to rear air flow
track along with two cross flow pockets to aide in motor cooling. The PKT mount comes in two
versions. A 28 x 92mm international specific version and a universal version. The
universal version will fit either 28 or 30mm frame rails and 90-92mm frame rail
spacing. The appropriate clamps will need to be selected. All hardware and
butterfly clamps are included. Finished in black oxide with laser engraving.
Sold individually.
Buy Now >>
Hardened 8 x 60mm Key with 6mm Pegs
1/17/2021
PKT'S 8 x 60mm Axle Key w/2 6mm pegs on 30mm center spacing is used on PKT 30mm and 40mm axles. For sprocket carriers, disc carriers & wheel hubs with 8mm keyways. Now comes in an optional hardened version. Sold individually.
Buy Now >>
PKT'S 6mm x 60mm Axle Key w/2 6mm pegs on 30mm spacing is used on our 30mm Kid Kart and Cadet Axles. For sprocket carriers, disc carriers & wheel hubs with 6mm keyways.
NEW Hardened version. Increased strength. All Keys sold individually.
Buy Now >>
Our new line of Performance Ceramic Axle Bearings have the following features: 40% less friction over its steel counter part. Less friction = More horsepower! 60% less rotating weight. Bearing life increased 3-5 times longer than steel. Lower vibration and cooler running.
Standard Kid Kart axle bearing has 52mm O.D.
"NEW" 62mm O.D. bearing for newer Birel Kid Karts. 2018 thru Current. Check your bearing sizes first.
Sold individually.
Buy Now >>
Buy Now >>
NEW PKT ROK Chainguard
10/17/2018
PKT's NEW ROK GP Chain Guard. Machined form billet 6061 aluminum with a black anodized finish. Mounting hardware included. Weighs 4 oz.Buy Now >>
New PKT Sprocket Carriers
9/16/2018
PKT's New UPDATED Lightweight High Quality Sprocket carriers. Available in 25mm, 30mm, 1.25", 40mm and 50mm sizes. Our 3 spoke 25mm carrier and 3 / 6 spoke 30mm and 1-1/4" carriers are all designed especially for Kid Karts and Cadets. We've updated the clamping hub to increase its strength. Machined now only with 8mm keyways. We have also added a 6mm locking set screw to keep the carriers from moving on the keys and to ensure a secure fit against the axle. These new features work well with the added torque of the LO206 motors. Finished in black anodize with laser engraving. All sprocket hardware included. Sold individually.
Note * Machined now only with 8mm keyway.
Buy Now >>
PKT Pinned Comer Jet Set
1/26/2018
The PKT Pinned Comer Jet Set is an accurate set of jets to make sure you get the best performance. Each jet is carefully pinned by super accurate gauge pins to determine the true size. This processes ensures the jet sizes are exact and eliminates any variability in size from manufacturing.
Includes jet sizes:
- .0240"
- .0245"
- .0250"
- .0255"
Buy Now >>
PKT's NEW NASA Panel Mount for GoPro
6/17/2017
PKT's NEW Driver Panel Mount for GoPro. Fits any GoPro. Made from high quality stainless steel with zinc plated bolts and nylon lock nuts. This mount has an angle designed to fit most driver panels and can be bent to fit your specific driver panel. GoPro case not included.Buy Now >>
Iame Bambino M1 60cc
3/31/2017
NOW Available
The M1 is the latest news in IAME's production. This small and compact 60cc power unit is designed to introduce the very youngest drivers to Karting and to make life as easy as possible to Dads and Mechanics. The M1 requires a very easy installation as all accessories are fixed on the engine block. The engine needs very low maintenence and basic service skills. It is provided with an easy and effective pull start system and a Tillotson diaphragm carburetor. The exhaust system stands with the engine and doesn't require the installation on the chassis. The simple 1.5l fuel tank completes the engine package. The M1 can be installed on 860/950mm wheelbase chassis. Safety is guaranteed by the cylinder/cylinder head and exhaust heat covers and a practical ON/OFF switch is located on the right side of the engine providing easy and immediate access to operators. The M1 is the power unit for the Drivers of the future and provides the perfect choice for Karting Trainers, Schools and Rental facilities. M1, the first step into Motorsport.
Engine Specs:
- Engine Type: OTTO / 2-Strokes Mono-cylinder
- Bore: 41.8mm (42mm max)
- Stroke: 43.30mm
- Displacement: 59.42cc (60cc)
- Max HP: 2 HP at 6500 RPM
- Max Torque: 2.5 NM (1.84 ft lbs) at 6000 RPM
- Inlet System: Piston Port
- Lubrication: 3% Fuel / Oil Mixture
- Ignition: Analogical
- Starting: Pull start
- Clutch: 3-mass Centrifugal Dry
- Max Clutch Engagement: 4000 RPM
Now Available
Buy Now >>
Iame Bambino M1 60cc Motor Mounts and Adaptor Plates
4/28/2017
Introducing PKT's New Kid Kart motor mounts and adaptor plates for the Iame Bambino M1 engine. This is an ongoing project with mounts and plates already engineered and manufactured for several chassis brands. If you're in need and your chassis is not listed below, please contact us.Buy Now >>
PKT 8x60mm Birel Key w/2 7.5mm Pegs
2/7/2017
PKT 8 x 60mm Key w/2 7.5mm Pegs on 30mm center distance that fit Birel 40 and 50mm axles. For sprocket carriers, disc carriers & wheel hubs with 8mm keyways. Sold individualy.
For Birel Axles
Buy Now >>
PKT Caster Camber Pill
7/18/2016
PKT's new Caster / Camber is a great solution for karts with 8mm king pins. Precise adjustments are now easily made. Locates in 12mm hole in C-hanger. Made from high strength stainless steel and furnished with set screw to stop rotation. Sold as a pair. King pins not included.Buy Now >>
PKT's New MyChron 5 OTK Gauge Mount
3/15/2016
PKT's NEW Mychron 5 Mount is used to adapt the gauge to an OTK (Tony Kart, Kosmic, Esprit & Alonso) 4 spoke steering wheel. The mount provides full access to the battery and rear ports. It fits on both straight and angled steering hubs. Made from .085" stainless steel to provide support and corrosion resistance. Sold individually.Buy Now >>
PKT Lanyard
3/7/2016
The PKT lanyard is pretty cool. Stuff attached to the lanyard is not included.Buy Now >>
PKT 30-960 Length Axle
3/7/2016
PKT's 30mm X 960mm cadet axles. Key spacing fits all 2 cycle karts. Used by national ranked drivers across the country. A must for those high grip situations. Please note different axle pictured. NOW keyed for 4 cycle too!
See below for PKT keys that fit this axle. Keep in mind that some aftermarket hubs, brake carriers & sprocket carriers may have different size keyways.
Buy Now >>
PKT Comer Carburetor Support
2/15/2016
PKT's New C50/51 Carburetor support bracket is a must to finish the race. This stainless steel bracket was designed specifically for helping to support the Dellorto carb and filter. There is a slot that allows carburetor movement on the intake manifold for tuning purposes. This bracket comes with longer special 4mm carb screw & 5mm head screw w/washer. Sold individually.
Buy Now >>
PKT's New Comer Crankcase Pressure Gauge
2/15/2016
PKT's new Comer crankcase pressure gauge is used to diagnose crankcase integrity. This gauge can be used to verify that the crankcase is sealed properly and is able to maintain correct crankcase pressure. Finding out if you have a bad seal or gasket is accomplished with ease. This makes this tool a vital part of any engine program. Current tech specs can vary. Check your racing series for current rules.
The other nice feature is that this tool can also be used to check pop off pressure. While the Comer C-51 has no pop off pressure, the Yamaha, Swift, Rok engine that you will be using in future cadet classes do. That adds even more value. Sold individually.
Buy Now >>
PKT's New OTK Master Wrench
12/18/2015
The OTK Master Wrench has both the bumper spanner wrench and the caster/camber spanner wrench in one tool. This product is a must for your toolbox. The Master Wrench is constructed from billet alloy steel and finished with gold zinc plating. Sold individually.Buy Now >>
PKT's Valve Spring Compressor
11/25/2015
PKT's new Honda, Clone & Preditor valve spring compressor. Used to compress the valve spring and release the valve. Fits Clone, Preditor, Honda GX200, GX270 & GX390. Sold individually.Buy Now >>
PKT's New Praga Components
3/11/2015
PKT's Praga Motor Mount
PKT's New C50/C51 motor mount for the Praga Kid Kart allows you to switch back and forth between the OEM Honda and the PKT Comer C50/C51 mount easily. It is made from light weight billet aluminum and features 2 stainless steel alignment bushings for easy adjustment. Furnished with all high quality zinc plated mounting hardware.
PKT's Praga Kid Kart Brake Caliper Bracket
PKT's New Praga caliper bracket has improved strength over the OEM bracket. This is a complete mounting kit that works with the Praga OEM Kid Kart rotor and the larger diameter Light Weight or Super Light Weight PKT kid kart rotor and hub. The kit includes everything you need including pre-drilled hardware for safety wire.
Buy Now >>
PKT's New OTK Pedal Extenders
3/1/2015
PKT's New Pedal Extender Kit for OTK (Tony Kart, Kosmic, Esprit & Alonso) magnesium pedals. The new kit provides 2 extended pedal positions at 20mm and 40mm toward the driver. These are great for the driver who needs to eliminate that extra unwanted reach. Finished in black anodizing. All mounting hardware included. Solds as a pair. Pedals not included.
Buy Now >>
PKT's New OTK Sniper Adaptor Kit
4/12/2014
PKT's New bolt on Sniper Adaptor Kit for OTK (Tony Kart, Kosmic, Esprit & Alonso) Chassis. If you are looking for linear front end adjustments for your chassis look no further. We have engineered a high quality kit that will allow you to bolt on this system at the track. The system includes 2 precision adaptor rings, 2 spherical sockets, 2 HD spherical washers, 2 king pins & zinc plated hardware to mount the system. The adaptor rings and spherical components are made from high quality stainless steel.
When installing this system you will use your existing lower spindle ride height spacer, lower OTK centralizing or eccentric pill, spacer, king pin nut and safety clip. Everything from the spindle down gets re-used.
Please note: NOT for use with front brakes.
-- UPDATE NOTICE #1 -- We have come up with new swivel balls that improve this system. This improvement minimizes alignment changes between the stand and the track. All of our inventory has been updated to this new improvement. If you have an existing system that you want to update please order the PKT Swivel Ball Update Kit below.
-- UPDATE NOTICE #2 -- We have come up with new HD washers that replaces the upper spherical washer and the upper OTK ride height spacer. The design basically combines the two creating a more robust system. All of our inventory has been updated to this new improvement. If you have an existing system that you want to update please order the PKT HD Washer Update Kit below.
Buy Now >>
PKT's New Seat Extenders
1/9/2015
PKT's New Seat Extender kit solves the problem of mounting extra small seats in cadet chassis's. Using these billet brackets allows you to bridge the gap between the strut and the seat. The kit includes all necessary mounting hardware.
Buy Now >>
PKT's New 30mm Axles
12/19/2014
PKT's 30mm X 1000mm cadet axles. Now with a Mini-Max legal axle. Key spacing fits all 2 cycle karts. Used by national ranked drivers across the country. A must for those high grip situations. Please note different axle pictured.
NOW keyed for 4 cycle too!
See below for PKT keys that fit this axle. Keep in mind that some aftermarket hubs, brake carriers & sprocket carriers may have different size keyways.
Buy Now >>
PKT's New 40mm Axles
12/19/2014
PKT's 40mm Axle line up. Both Chromemoly and Mild Steel. Very popular with cadets and with the Briggs LO206 karts.
See below for PKT keys that fit this axle. Keep in mind that some aftermarket hubs, brake carriers & sprocket carriers may have different size keyways.
Buy Now >>
PKT's New Lightweight DWT Kid Kart Wheels
7/16/2014
PKT's Lightweight DWT Wheel are 9.25% lighter than the standard wheels. A cool new look to the old kid kart wheel. The hot set up to increase tire circumference and decrease rolling resistance. All this while running lower tire pressures. These wheels are precision machined for maximum balance and performance. Legal most all clubs and series except Route 66 Kid kart class. Sold individually.
Buy Now >>
PKT's New Lightweight 30mm Wheel Hubs
4/12/2014
PKT's New Lightweight 30mm metric wheel hubs. Available in 50mm & 70mm lengths with 6mm keyway's. 50mm weighs 8 oz. & the 70mm 9 oz. Finished in black anodize with laser engraving. Sold Individually. 2 required.